Mossberg 500 Magazine Tube Removal Company

Saturday, 6 July 2024

The parts of your Mossberg 500 shotgun that need to be lubricated are the bolt assembly, receiver, and any other metal parts. Any suggestions how I can get this thing off without causing damage? These instructions break the shotgun down into 10 parts. Squeeze the legs of the lifter and slide the assembly out of the bottom of the receiver. Frequently Asked Questions. Finally, you will need to remove the barrel from the receiver.

  1. Mossberg 500 magazine tube removal tool
  2. Mossberg 500 magazine removal
  3. Mossberg 500 magazine tube cap removal
  4. Mossberg 500 magazine tube and barrel

Mossberg 500 Magazine Tube Removal Tool

If it won't budge use a torch to soften the Loc-Tite. F. Once all shotshells have been removed, physically and visually check the magazine tube to ensure there is no ammunition left in the magazine. You should use a gun oil or other suitable lubricant. Finally, wipe down the stock and forend assembly with a damp cloth. Pull the bolt slide down and out of the bottom of the receiver. With the trigger assembly removed, you can now remove the bolt assembly. Thread Tools||Display Modes|. Remove trigger pin by pushing it out. Remove the Trigger Group Retaining Pin (just above the trigger). TFB FIELD STRIP: MOSSBERG 500 SHOTGUNS. Or is there a local gunsmith willing to help me out?

The Bolt is removed from the front of the receiver, where the barrel had been. Repeat this process until all shotshells have been removed from the magazine. Now that you have the shotgun disassembled, you can clean it thoroughly. Do this carefully with a propane torch. Once you have the gun back together, you can now clean it. I have a new Mossberg 500. Disassembling a Mossberg 500 shotgun can be learned and mastered quickly.

Mossberg 500 Magazine Removal

The field strip process for the Mossberg 500 is very similar to the 505, 510, 535, 590, 835, as well as the Maverick 88 and 91 models. Keep your finger off the trigger until your sights are on the target. To do this, first remove the stock from the receiver. With the barrel removed, you can now take out the action slide assembly. The bolt can now be removed from the receiver by pulling it to the rear and then up and out. Before we get started, the four gun safety rules are listed below as a reminder. Remove the spring and follower from the magazine tube.

Continue reading here: Mossberg Models Are Designed To Fire And Gauge Shotshells Only. Reassemble in reverse order and complete a function check before storing your Mossberg 500. You may have to fully or partially close the action while doing this. I know what you are asking, "why do I want to remove the magazine tube? " Plus facilitates recurring maintenance. All the subsequent times, the magazine tube unscrewed normally, real easily like it should. With the trigger group removed, they are free to fall out of place. With proper cleaning and maintenance, your Mossberg 500 should last for many years. It works great and is smoother than silk. Tools you will need to disassemble your shotgun. Before I go caveman on this thing I was hoping one of you experts had a suggestion. If you're simply replacing the follower and spring all you need to do is remove the magazine cap that holds the barrel in place and pry out the keeper that holds the spring and follower.

Mossberg 500 Magazine Tube Cap Removal

Three word come to mind when I think about taking mine apart for the first time: A Fu@king Pain in the Ass. Assuming you are referring to the process of disassembling a Mossberg 500 for cleaning purposes, the following tips may be helpful: - First and foremost, make sure the gun is unloaded and the safety is engaged. The final step is to remove the safety button by pushing it in and turning it counterclockwise. Dog, just take a common screwdriver and a folded rag. Then, apply a light coat of oil to the action slide assembly. Next, clean the action slide assembly, being sure to remove any dirt or debris from the inside of the action. Tips and tricks for disassembling and cleaning your shotgun. I know sometimes there's loctite on the threads and some heat will help, I'm reluctant to do it because I don't have a replacement follower and don't want to do any damage. But now I can't get the damned trigger assembly back in--ive been trying for like an hour and a half. A cleaning rod and brush.

With a little practice, you will be able to disassemble and reassemble your shotgun quickly and easily. There is more than one red Loctite. The 590s that my platoon had in Iraq were easily stripped down to their bare receivers, but my own personal 500s are a PITA. I have done it before. You may have to put the receiver in a padded vice and crank away if it's a tough one.

Mossberg 500 Magazine Tube And Barrel

We've previously discussed how new ammunition developments have made the shotgun more valuable than ever as a lethal tool, but regardless of whether yours is reserved for launching buckshot or beanbags, you need to keep it clean and ready for service. That tube is stuck tight. Pull the action forward and line up the carrier with slots in the receiver, to remove the carrier. Working the action slowly will allow you to safely capture the ejected shotshell. The first step is to remove the stock by unscrewing the two bolts that hold it in place. Next, remove the barrel by unscrewing the magazine tube nut. The only tool required is a punch or something similar (small screwdriver, Allen wrench, or even a pen). Recommend that while you have it out clean the magazine tube and lubricate the spring before reinstalling. This shotgun has literally been fully loaded for almost 15 years, the magazine spring is so weak it can barely push out the last 2 shells. Remove the magazine tube cap, which is located at the end of the magazine tube, by unscrewing it counter-clockwise. Once the trigger group is removed the Cartridge Interrupter (red arrow) and Cartridge Stop bars can be removed. I'm trying CA glue debonder now. I scuffed mine a little (nothing serious though) so be prepared to pad the vice and whatever wrench you use.

I finally consulted my local gunsmith and he told me they used black Loctite to secure the tube. Next, unscrew the action bars retaining screw and remove the action bars. The cartridge stop and cartridge interrupter are held in place only by the trigger group. It wasn't that difficult with a little leverage!

Been using them for years and swear by them). Grasp the barrel and forearm to prevent them from sliding forward. Turn the receiver with a cresent wrench with a fair amount of painters (blue) tape on the jaws so you don't mar your receiver. This can cause serious malfunctions in the firearm's operation endangering the operator and those nearby. The final step is to remove the forend from the barrel. Move the forearm to a middle position where the action is halfway open. First, loosen the action slide lock, which is located behind the trigger guard. Make sure the safety is on (safety button pushed reward with no red dot showing). Unscrew the Takedown Screw (or magazine cap for similar models) at the end of the magazine. Simply reinstall the barrel and push the spring in while installing the screw cap. Be careful when removing the bolt as the bolt spring is under tension and can cause the bolt to fly out of the receiver. First, you will need to remove the magazine cap, which is located at the end of the magazine tube. The grips have to be attached where the barrel screws into the magazine tube, it is the thickest part of the tube and can withstand the clamping force.