Where To Cut Hole In Truck Bed For Fuel Pump

Saturday, 6 July 2024

15x8 Pacer 164P Polished Wheels | 31x10. 1997 4WD Chevrolet Silverado Extended Cab Short Bed (purchased new January 1997). Honestly, I didn't even break a sweat. Was able to hold off with a modded no hub clamp til I get a new neck. Unplug taillight harness. I have a 1987 sr5 extended cab and here is a picture of the truck without the new oem bed installed. I'd highly suggest dropping the tank. Access to the Fuel Pump. Originally Posted by Rango88. I will be fined 1500. Register to join our community. But when the fuel gets low enough to where it doesent slosh up and fill the void then it runs like crap. I have carpet in my bed with a cover. Slide bedliner back in place.

Where To Cut Hole In Truck Bed For Fuel Pump Problems

Dont f+ck with Ch+ck. I did one to a 97 that I had, dropped tank but didn't lift box. Yeah well, I don't have one of those". But this truck is neither nice or ever taken care of. Sold/Totaled: 2006 Ranger XLT 2D SuperCap 4x4 Torch Red. Also I have seen where guys cant get the bolts out or snap them off.

Reverse the process to put the new pump in. Some of the lines are within a couple of inches. I want to cut a hole in the floor above the pump opening in the tank so it is easier to access next time. Location: New Jersey. Cutting access hatch in bed to fuel tanks. Blood type; Retumbo. Reason I was having fuel pump failures was because of bad design of connector. 269, 000 Miles as of 11/1/2013---If its a Ford you will need to keep a lot of tools and a good fire extinguisher handy. 1999 GMC Yukon 350/4L60 4" SAS. With a little finesse and colorful language, you should be able to slide the two sections apart. The only reason I mentioned cutting a access hole was because I saw it in another thread about doing a fuel pump and sending unit and someone did it.

Where To Cut Hole In Truck Bed For Fuel Pump

You should now have the pump and it's carrier in your hand. I see so many rupture behind the tank that I sell people a new brake line when I do a pump. Last edited by shifty; 04-02-2019 at 10:26 PM. So taking off the bed and leaving it at my house is out of the question. Just jump in and the ignition switch works with or without a key! It will be necessary to cut the access panel on the floor of the bed. Replaced many over the years. Hardcore Ford Truck Fanatic. Now you should be able to get to the pump on the top of the tank. Fuel pump replacement help. If your a CC, cutting a hole in the rear of the cab, really?.

The pump is almost always going to be located in or on the fuel tank, but the exact location will vary depending on the make and model of your truck. Truck: 2007 F150 Lariat 4x4. 1969 Mercury Cougar Standard 4 speed. Was causing the pumps to go bad. You can order replacement Hex tap bolts from (much cheaper). 1969 Mercury Cougar XR7 convertible. I know, probably seems like I'm fixing everything in my truck right now, that's not lost on me! Ford Factory Trained, Gasoline and Diesel. Never heard similar on my '03... Realistically, will the Delco part outlast a very well known name brand like Bosch, and is there actually a difference between the Delphi and AC Delco part for a 97/98 5. Thanks for the bolt information I have bought bolts from that site too. Take the bed off..... Where to cut hole in truck bed for fuel pump. Re: Cut Access Hole In Bed For Fuel Pump. Other Fords owned: 00 Taurus, 96 T-Bird, 95 Escort GT, 93 Mustang 5.

Where To Cut Hole In Truck Bed For Fuel Pump Diagram

I have a 2016 GMC Sierra 1500 crew cab 5. The side cuts just have to be in the low points of the bed, they are not so critical. Climb under the truck and take out the 6 bolts (15mm on my 2001 2500) that hold the bed down. Has anyone done this? Yup and license plate light connector. Re: I smell a cheap replacement pump. Communicate privately with other Tundra owners from around the world. IMO can't replace without doing at least one. Paint the metal strip, rivets, edges of the hatch and think about further sealing the edge of the hatch with RTV after the paint dries. 04-02-2019, 10:18 PM||# 23|. Where to cut hole in truck bed for fuel pump troubleshooting. 0, 5 speed, 4WABS, crank windows, no cruise, Edge 116k. Where can I find a diagram showing where the fuel.

Location: next to my reloading bench. 2004 Ranger, Ext Cab, 2WD, 3. Man rule you own a 67 stepside with a caddy 472 you will never be in danger of loosing you man card. Posts: 12, 688. yes just take the damn bed off. Since this is the second pump to go in less then a year... Now, get three long, thin screwdrivers or punches and put one between the two sections right by where the little locking tabs are that keep the bottom from dropping off. The fuel tank is located behind the cab. 2014 F150 SuperCrew XLT 4x4. 0 v8 |Tow Package | Oxford White. Quote: Originally Posted by 4Banger5speed. Where to cut hole in truck bed for fuel pump diagram. 10-30-2012, 03:37 AM.

Where To Cut Hole In Truck Bed For Fuel Pump Troubleshooting

2001 Ford Ranger Supercab (4dr), Oxford White, 4. Don't rush once seal is broken its a matter of working the bolts out... Can't hurt to give the bolts a controlled tap or two with hammer or light sledge. I was hoping that person would chime in. Cranked but no start, showing code p023f.

I do have a drop in liner so it's covered up and you cant see the hole when the liner is in place. That way the hole will be there when ever I DO need or want to do the other maintenance. Unless you think you'll need to access the fuel pump often, there may be better options than cutting a hole in your truck bed to reach the fuel pump. I read somewhere briefly about someone cutting a hole in the bed above the fuel tank. But seriously, if you have an engine hoist, it's easy. Join Date: Oct 2009. Members can start their own topics & subscribe to topics. 2 guys can easily do an F-150 or a ranger bed. DO NOT DROP THE TANK!! This is a ratty truck anyway and I couldnt care less about what it looks like. It won't be the same for every truck.

Dropping the tank is not bad, it's just seems that I always have a full tank of gas when mine dies. 2001 Ford Ranger with the flare sides. I will be giving it a try. Even if its a throwaway truck, dont cut corners like this.. 10-29-2012, 11:43 AM.