Torque Spec Valve Cover Tightening Sequence

Thursday, 11 July 2024

After a few heat cycles, check and tighten then up as necessary. Car: chevy camaro 1987 z28. © 2023 MH Sub I, LLC dba Internet Brands. A photo schematic or link to one would be much appreciated as well, if available. Both driver's and passenger's sides. On a positive note you do not need to remove the Cam Positioning Actuator on the driver side so it just one less thing to deal with (however you should still unplug it). I haven't tried the new silicone rubber ones yet, but hopefully soon! They are a "shanked" bolt, so NO matter how tight you do them you will not pull the cover down any tighter on the seals. As a refresher here are the order and the specs for the valve cover and the throttle body: 2 Rounds of torque. Tech / General Engine. 2012 Volvo S60 R-Design. In that case, follow the instructions here to regain access to the forum. Hi all, can anyone please tell me the proper sequence for torquing the valve cover fasteners on my 2005 BEW Golf? Can someone with access to a service manual tell me the order and torque specs for a 2008 2.

Torque Spec Valve Cover Tightening Sequence Pdf

There possibly is a setting somewhere, but honestly I have never bothered. 3 years since i have had them off and no leaks. Axle/Gears: 9 bolt 3. It doesn't mention any liquid gasket for n/a SOHC engine. 4. yea i got some real nice felpro gaskets but dont know what rtv is, right now they are jsut hand tightened on there, thanx. I realize it's an old thread, but ran across this doing some cam-cover research and thought I'd add the answer according to that there's anything at all wrong with the sage advice posted by Grand and Doug! The turbo DOHC has directions on where to apply liquid gasket. Now lets talk torque spec and order. I know in the video I talk about the specs and order of the bolts on the valve cover and the throttle body but I want to include a few more. I also make a habit of snugging the bottom row first.

Torque Spec Valve Cover Tightening Sequence Maintenance

Valve Cover Gasket- Torque Specs and Order. 68 Impala, 15 SantaFe. Go around the outside again, working diagonally. Please register or login to enable Dark Mode. If you have the standard sbc heads a neat trick is to use rtv on the top of the gasket and a thin later of axle grease on the bottom. Start all the bolts a few threads by hand, and then run them down with the socket till they just barely touch the cover. Transmission: 700r4. I will be changing my valve cover gaskets soon and was wondering if it was necessary or recommended to change the grommets on the bolts. Location: Centennial, ColoradoVehicle: 08 Impreza, 80Vette. 09-27-2015 01:53 AM. These are all 10mm bolts. I can't find the info anywhere and I'm changing all the top end gaskets in my C5 and I was wondering if anyone had the torque specs for the valve cover and cam tensioner bolts? Received 1 Like on 1 Post.

Valve Cover Tightening Sequence

Yep, which is why they always leaked over time and people used gasket sealer to prevent it. Privacy Statement -. The valve cover is easier to clean than the head. Last edited by SLEEPER 86; 10-23-2005 at 09:03 AM.

Torque Spec Valve Cover Tightening Sequence Wrench

The only downsides are if your space is limited and sliding the valve cover down over the studs is difficult or impossible. Audi and the Audi logo(s) are copyright/trademark Audi AG. Engine: bored out 305. But if you've got the space, they're a good call. When I did the video I performed the job on the passenger side. I have ordered parts from them before.

Torque Spec Valve Cover Tightening Sequence Size

Other than that the job is just about the same. Join Date: Nov 2007. With the spark plug gaskets hardware in the valley barely snug, it's time to the work around the outer edges of the cover. Thanks very much, in advance. Torque-wise, snug plus a little is plenty. Gaskets and RTV as mentioned above. About the cost of one oil change. It's not a critical thing. Manage Preferences -. These are a single round at 74 in-lbs. This post references the Ry The Car Guy video below. Location: Providence, RI, USAVehicle: 2018 Crosstrek CVT. In order to log in after the forum software change, you need to reset your password.

Torque Spec Valve Cover Tightening Sequence Cost

Software Upgraded - Reset Your Password to Login. The nuts and the bolts for the collector go in at 8 ft-lbs in the following order. And nobody has helped with the tightening sequence. GT2860R-7 S4 Build Log--. When you are you reassembling be damn sure that you are not forgetting to plug anything back in! Axle/Gears: stock pegleg 2.

Torque Spec For Valve Cover Bolts

Your Broken/Sheared OEM Axles--. The cover is pretty thick on the edges, so you can go a little tighter without worry of cracking the cover except for those two in the center on the timing belt end of the cover, just barely snug those. Which translates roughly to 6 ft-lbs. Location: Saskatoon, SK, Canada. Just tighten them a bit so they snug down, but not overtightened so that you warp the gasket surface. Common sense is the main thing here really. 08-29-2015 03:16 PM. Transmission: 700r4, 2200-2400 stall, vette servo. Go back to the center of the cover and snug the bolts up a lil tighter in the valley working from the center out. Do one final pass and bring everything up to the correct torque values. Ubbthreads/images/graemlins/. Location: Birmingham, ALVehicle: 2016 Lapis Blue STi.

08-25-2015 11:49 PM. Step 2: Looking at the cover, the sequence is: top-center, bottom-center, top-right, bottom-left, bottom-right, top-left. Location: Toledo, OH. If you are looking for the gaskets I used in the video they are here: and here is the gasket maker I used as well: Tools I used on the job: 10mm Socket. The lion share of work is just getting to the covers, actually swapping out the gaskets is really not that big of a deal. I'll post results when i try them. There are a few additional connectors on the driver side including the O2 sensor wire leading to the exhaust. You will be kicking yourself if you removed a fuel injector plug under that intake collector and have to remove it all to plug one little thing back in.