Puffco Peak Short Circuit Fix

Tuesday, 30 July 2024

Note: In my video, I perform step 5 before step 4 – and it really doesn't matter in the end, but I feel it's easier in this order. It will lift off, and may require a twisting motion or a small amount of heat if it feels stuck. Place your fingers above the USB port where the shiny material and silicone meet and pry upwards on the shiny metal/plastic piece that surrounds the Puffco Peak. It may help to warm this area with a hair dryer or gently using a heat gun.

  1. Puffco peak short circuit fix blog
  2. Puffco peak short circuit fix 3
  3. Puffco peak short circuit fix 1
  4. Puffco peak short circuit fix how to

Puffco Peak Short Circuit Fix Blog

If you have done this before it makes sense, otherwise: read on. Step 2: Pry the Shiny Metal Piece Upwards. If it feels stuck, apply a small amount of heat and try again. Step 1: Remove the Atomizer & Surrounding Components. Next steps are to poke around a bit more, and see if rescuing this battery back above it's rated voltage is enough to keep it working. This faulty Puffco Peak vaporizer came into my possession within the last few weeks, via a friend of mine. Unscrew the metal housing for the heater by turning it counter clockwise several times to disengage the threads. I was told, "It doesn't charge – it's broken. Let's assume you don't need a hand in figuring out how to remove the glass from your puffco. These devices are simple, and with that in mind; there shouldn't be too many ways for the device to fail.

Puffco Peak Short Circuit Fix 3

If anyone has input, questions or ideas – I would love to hear them in the comments below or on the Youtube video linked above. Lift the entire component out of the silicone well. This can be removed as one whole piece, or disassembled and removed piece by piece. This piece is glued in place, and requires a small amount of force to lift. Use a screwdriver set like this one from Amazon to remove the three screws holding the plastic assembly together. Step 5: Unscrew 3 Security Screws. I assume that this is the case, because when I apply 7. The teardown video is up on Youtube now: Step by Step Instructions: How to Open a Puffco Peak. The Puffco lights up, and indicates it's taking a charge when plugged in to USB. The silicone will lift out from under the shiny metal base of the Puffco. Be careful and go slow. Step 3: Remove the Silicone Boot. 4v battery pack – unless there were a buck converter somewhere on the battery pack I have yet to find. If that isn't the case, I'll be adding an external battery pack to make up for the lack of internal charge circuit.

Puffco Peak Short Circuit Fix 1

Step 4: Pry the Metal Base Off. 5v to the battery connection leads – the battery charges and holds its charge. Begin the disassembly process by removing the atomizer, bucket, and surrounding components. Step 6: Open and Inspect. Checking the voltage supplied to the battery while plugged into USB showed only 4. We're starting off with a standard Puffco Peak base – glass removed. My puffco wont heat up, instead it blinks 5 times, on whichever heat setting i have it on. In my case – I did some poking around with a multimeter and determined that my battery was not putting out a high enough voltage. The adhesive is fairly strong, and so some force is required to remove this piece.

Puffco Peak Short Circuit Fix How To

I took it apart and cleaned the whole thing pretty well, i thought that would at least solve the connection issue, but it didnt seem to fix it): any tips or any help will be appreciated! This is the most confusing part of this disassembly, and I suggest you watch the video starting from about the 1:00 minute mark for a video example. One of these screws is below a security sticker, revealing silver 'VOID' markings when removed. The bucket rests directly atop the heating element – extract can glue it in place – and tugging on the element can damage it's fragile connecting wires. Remove all three screws, and your Puffco will almost fall apart in your hands. You may use a guitar pick or some other soft plastic prying tool to start the job if your fingers can't get in there.

Ideally, finding out which component has failed; and swapping it for a working one is best – but my electronics skills are limited.