How Many Leaf Springs Can I Remove

Thursday, 11 July 2024

How many leaf's should i take from each pack? I'd look at different shocks to smooth the ride out if its too harsh or bouncy, whatever your concern is. If it is below the full line, add fluid to the full line. Removing Leaves Causes Handling Issues. There's a nut on top to take off, then after the end clamps are removed the pack will fall apart. Or remove one leaf and leave the overload, or don't do this at all? Repeat the steps to install the replacement spring on the other tire.

  1. How to replace leaf springs
  2. How many leaf springs can i remove account
  3. What size leaf springs do i need

How To Replace Leaf Springs

Then, crank the jack until the tires are 3 in (7. I don't want to break a spring on the trail but need the body to be more independant of the rear axle. 3/8-inch ratchet and socket set.

Forgot about the u-bolts and center bolts. Test the vehicle's stability on the jacks before attempting to remove the leaf springs. The bolts are horseshoe-shaped, so they are very distinct and noticeable next to the leaf spring. Rmoving load from leaf springs for shackles. I like the way you thinkJames72 wrote:If you're getting new springs anyways, why not just torch the ends off that bottom overload leaf? I have a local spring and axle shop, that can take springs and rearch them to what you want. Then, lower the floor jack to put the car safely on the ground with its new leaf springs. Likely, you are replacing the leaf springs because - over the last couple of decades - you've simply worn out your existing springs and they are now sagging. And I've put a lot of miles on them since then. Kent, A spring is designed so each leaf is equally as important as the next one.

9/16" Heavy Duty u-bolts: 110 ft-lbs. Look to see if one spring is flatter than the other, in which case the car will probably have a pronounced tilt to one side. I thought there should be a normal mount on the rear (where the mount has a horizontal stub for the shock to slide onto). I did a few searches and came up empty.

How Many Leaf Springs Can I Remove Account

Axle wrap in the rear might be more of an issue- but not too much with a 4cyl, CV, and 33s. There are metal clips on them that would need to be pried open. How to replace leaf springs. I was also scared of losing the rear universal joint because the weak springs were now allowing axle housing rotating. The leaf spring suspension has been around since before the Model T and has been used for more than 100 years because of its high load capacity as well as its ease of use. Position the floor jack and a sturdy piece of wood under the trailer receiver and raise the jack until the leaf pack relaxes and is not under pressure.

Don't for get the video camera. But if it breaks down as fast as I fear it will, it will not have been worth the effort. Two jack stands are now supporting one side of the truck. What size leaf springs do i need. The springs will ride smoother and hopefully be more flexible. Join Date: Mar 2010. If it is higher than the shackle, lower the rear axle or raise the frame slightly (as in step 1a or 1b) so that the rear leaf eye is aligned with the rear shackle. 55 sure grip I would like maybe 2 inch drop in the rear but would drop shackles alone make it wheel hop?

Pick up the end near the front of the tire. It can be considered suspension tuning by the Ouija method. Torque the u-bolts to: - Toyota OEM u-bolts: 90 ft-lbs. He said if the springs start to sag- I should just put those back in. Its kind of just trial and error. The rear also sits a little higher than the front since there's not enough weight in the rear to make them compress at all. How many leaf springs can i remove account. Relocate the springs or have the same set de arched by a truck shop. Replacing them with a stock replacement will mean that you maintain the relatively soft ride of a stock Tacoma, can carry moderately heavy loads rarely, and are not looking for additional lift (beyond lifting the truck back to its original height - which may be 2-3" higher than where it sits with worn leaf springs).

What Size Leaf Springs Do I Need

Last edited by 98RAM1500; 05/11/16 10:27 PM. I'm afraid to install them. Otherwise, the (short) stock brake line could be broken as it is forced to stretch a longer distance between its two attachment points - one on the frame and the other on the rear axle. Extended rear shocks - Any leaf spring that lifts the rear end of the Tacoma above stock should be paired with a new set of rear shocks so that the leaf spring travel is not limited by the stock shocks. AllDataDIY – The DIY Repair Solution. I have around 9 inches of space between the top of tires and fender lip looks like the trucks going up hill. Regardless, each option brings tradeoffs in terms of cost, ride, additional lift, and durability. I. don't plan on taking them out... Removing a leaf on a pro comp 6" front leaf spring. ". If the rubber bush is in good condition, there should be no sideways movement of the spring. The top 4 are wrapped. Any advice is appreciated. Thanks in advance for any good help. This guide outlines - but does not focus on - those operations, to the extent possible. It is a lot safer than just tossing out springs & hoping the result will work and you will likely get better results.

Next I'll go after the rear springs to m ake it more level. Peter60 wrote:Just wondering what the thoughts are about removing one or more leaves from the front and rear leaf springs...... A old series 1 Land Rover got to about 500mm. Side play was around a 1/4" on either side of the. You know, something that just dawned on me is the fact that the F100 springs I pictured above from my choptop are quite a bit thinner than F250 least when compared to the F250 Camper Special setup. 30 over 318 4bbl with 444 lift cam and A999 auto trans with 9 1/4 with 3. Got to buy some Rancho's too so i can get those in. Unbolt that bolt, using the 3/8-inch ratchet and socket and an open-end wrench. "The information I was looking for was all here, explained in layman's terms and easy to follow. 1) Extended rear brake line, at least 20" in length. Next 2 pics were taken today at rest on level ground. Here's a pic from when I installed mine.

Thanks for any insight.. S. # 2. Fit the other end of the spring in the square-shaped bracket at the back end of the wheel. Removing leafs from a pack is a guessing game of sorts. They really do ride nice with none of the mixed luck we see in para reviews. You can see how the other leaves aren't being supported and are starting to sag. I broke the folding tabs off on my clamps, too. Inside Length (diameter of axle housing): 3". Note: General Spring lists these as 98-00, but they fit 98-04.