3.6L Engine Oil Cooler + Intake Manifold Issues

Thursday, 11 July 2024

A chain drive replaces the usual timing belt, for greater longevity and accuracy. The 8 main bolts located on the sides of the cylinder heads should be torqued down to. Oil Leak] Oil filter housing leak again. Failed twice in 3 years. However, your driving habits and conditions (temperature, off-road use) do play a part in this duration as well. Has anyone actually done this upgrade with the Pacifica? Piston cooling jets are fitted to each cylinder, spraying oil onto the piston to prevent detonation, control heat, and allow MDS in the future. Copper spray from permatex on the exhaust manifold gaskets to ensure I do not end up with.

3.6L Pentastar Oil Cooler Torque Specs Problems

Shock Absorber Upper Bolts. The feed is at the upper rear of the cylinder on the bank you can see, what appears to be a hole next to the head bolt. Bolt, reaction shaft support. Can use a tool to move the tensioner into its springed state and install the belt as shown in the. Oil to antifreeze oil cooler in the "V". Two-piece upper half thrust bearings at located at the #2 main bearing; they are installed with the oil groves facing outward. Crankshaft Main Bearing Cap Cross Bolts (3. Oil filter torque spec. So for just about anyone, 5W-20 oil works the best unless you are in a warmer climate or only run the vehicle during hot summer months. Upper fender fasteners. For installation of the new housing follow the provided ALL-DATA pages for proper torque values and patterns. Door latch striker bolts. Hub/Bearing Axle Nut. That ranges from the crankshaft sprocket to the idler sprocket. When the oil is hot and thinner, more oil is needed, and a spring increases the size of the pump chambers.

3.6L Pentastar Oil Cooler Torque Specs Manual

Finally the throttle body can be installed on top of the intake manifold. Rear Wiper Arm Mounting Nut. Direct replacement for a proper fit every time. Screw, plate to oil pump body. Three oil drain back drillings are on each of the cylinder banks, and two knock sensors are in the block valley. 3.6l pentastar oil cooler torque specs manual. I was able to carefully remove all the fuel injector plugs with a screw driver. Power Steering Pump Pressure Line. Bolt, Fluid Filter-to-Valve Body. Pull hose and drain. This part has undergone a rigorous inspection to ensure high quality. Once the rings have been installed you can now fit the connecting rod bearings into the end caps. Want to be leaking gas fumes around the engine.

3.6L Pentastar Oil Cooler Torque Specs Parts

It also includes all the necessary gaskets for an effective repair. The oil filter will remain attached to the cap, and will have a bit of oil leaking off it when you remove, so keep a towel handy to capture any renegade oil. Steering Damper Tie Rod nut. Remove 10mm nuts on the bracket located on the right side of the intake neck, behind the throttle body. Very basic tools needed for this job other then a torque wrench and #8 external torx socket. 3.6l pentastar oil cooler torque specs.html. You absolutely want to have a quality torque wrench. We offer a line of Engine Oil Filter Housings for a wide range of applications. 6L engine gets tightened down to the engine block on the inside and is ran off of the timing chain.

3.6L Pentastar Oil Cooler Torque Specs Diagram

As long as everything looks good, shut off the engine and give it a minute or two for all the oil to drain to the bottom of the engine. I was able to see a little bit of pooled oil looking in between the oil filter housing and the intake. First remove both plugs from the rear of the adaptor housing. Does the Dorman product fit exactly? Bolt, Output Speed-to-Case Sensor. Piston and Connecting Rod Installation. The engine features high-flow intake and exhaust ports, which in combination with dual independent cam phasing, allows optimum volumetric and combustion efficiency over the full speed and load range. Intake Manifold – Lower Gasket Retainer-Bolts. 3.6l pentastar oil cooler torque specs diagram. Front seat mounting bolts. Dipstick Tube (sump). Easy, You will see MOTOR oil on your upper and lower transmission bell housing. The primary chain guides and tensioners need to be torqued down to 8 ft-lbs. Owners of other Jeep, Chrysler, RAM, Volkswagen, Fiat and Lancia vehicles equipped with the Pentastar 3. Bolt, Converter-to-Driveplate.

3.6L Pentastar Oil Cooler Torque Specs.Html

I'm preparing to do an oil cooler on a 2014, and I'm seeing a bunch of different/conflicting torque specs for the intake manifolds. Timing Cover Installation. Double check that the rubber o-ring and new cartridge filter are properly installed on the cap. Power Steering Gear Adjustment Screw Locknut. Then by using the exhaust manifold gasket and putting it in place.

Before starting this project, make sure you park your Wrangler on level, flat ground and verify you've set the parking brake. Tighten With 24mm Socket. Note: I am not a registered charity. Cylinders are numbered front to rear; the right bank has pistons 1, 3, and 5, the left 2, 4, and 6, with a 1-2-3-4-5-6 firing order. No more having to trust the shop with those important, but sometimes overlooked, details. It is recommended to replace both the seals. 2014 Cherokee Trailhawk V6 3.2L , Oil fitler housing leaking. Power Steering Pump. The engine also can run on E85 blended gasoline. I removed the 10mm bolt on each side in order to remove the two brackets. Cleaned out before placing the manifold into position. With the gaskets in place you can now put. Center High Mounted Stop Lamp (CHMSL) Mounting Screws.

Intake Manifold Upper-Bolts. Liquid Line to Condenser Nut. Bolts, Radiator Upper Isolator to Crossmember. 24mm Socket for oil filter. Four door retractor screw. During installation. Click the area you are looking for!

Bolt, Park Sprag Retainer. Bolts, Condenser to Radiator.